2024 Vermeer® Stump Cutters SC382

Information

2024 Vermeer® Stump Cutters SC382

This SC382 Vermeer stump cutter is equipped with a 37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine. The optimized cutting wheel on the SC382 gives this machine aggressive cutting capabilities.

Features may include:

Standard four-wheel drive

The SC382 stump cutter is equipped with standard four-wheel drive to offer traction and maneuverability in difficult transport conditions.

Operator presence system

The operator presence system is intended to enhance operator safety by automatically stopping the cutter wheel when the operator releases the hydraulic cutter wheel controls.

37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine

The SC382 stump cutter has a 37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine.

Photos

Highlights

  • Texarkana, Texas
  • 2024
  • Vermeer®
  • Stump Cutters SC382
  • Gas
  • Available
  • 50.1 in
  • 53 in

Specifications

  • 2024
  • Vermeer®
  • Stump Cutters
  • SC382
  • Stump
  • Briggs & Stratton Vanguard
  • EFI
  • 2
  • Gross (Maximum): 37 hp
  • 49 ft-lb
  • Dry-type safety element and restriction indicator
  • Spin-on
  • Medium: Air
  • Max Fuel Consumption: 3.2 gph
  • Gas
  • Electric clutch with brake
  • Steerable Axle Type: Hydraulic steering, oscillating axle
  • Rigid/fixed (rear)
  • 5.7"x 8" (14.5 x 20.3 cm) dual standard
  • Spring-applied, hydraulic release at rear motors
  • 400 CCA
  • 20/50 amp (rpm-based)
  • System Voltage: 12 V | Shutdown System: Engine low oil pressure
  • Cutterwheel: 1560 rpm | Low Speed Travel: 65 ft/min | High Speed Travel: 130 ft/min
  • System Type: Open-loop series system
  • Flow at Maximum RPM: 6.4 gpm
  • System relief: 2470 psi
  • Welded tube and plate steel
  • Warning: Oil pressure, engine fault, operator presence status, clutch engage/disengage status
  • Maximum Angle of Continuous Operation: 25 deg | Cutterwheel Diameter without Teeth: 17 in | Cutterwheel Thickness: .5 in | Cutterwheel Straight Line Dimension: 47 in | Cutterwheel Cut Above Ground: 24 in | Cutterwheel Cut Below Ground: 15 in | Chip Containment: 7.5 cu ft | Jackshaft Dimension: 1.3 | Bearing Dimensions: 1.3 bore | Cutterwheel Shaft: 1.8" (4.8 cm) | Bearing Dimensions - Secondary Belt: 1.8" (4.8 cm) double spherical roller pillow block | Degree of Oscillation: 12 deg | Blade Travel Above Ground: 8 in | Blade Travel Below Ground: 2.5 in
  • 118 in
  • 50.1 in
  • 53 in
  • Transport (without duals): 35.5 in
  • Tank: 10 gal
  • Volume with Filter: 2.5 qt
  • Tank: 6.5 gal
  • 1950 lbs
  • Number of Teeth: 20 | Number of Indexes: 2 | Number of Pockets/Teeth: 20 | Jackshaft Bearing Type: Sealed ball | Filtration Method: 10 micron fill strainer and 6 micron return filter | Flow Control: SmartSweep | Directional Control: Electric over hydraulic | Switches: Two-speed 2x4 and 4x4 ground drive, cutter wheel engage/disengage, creep, blade (if applicable) | Controller: Danfoss | Control Station Description: Fixed side location | Axle: Rigid
  • Recommended: 10W30 | hydraulic Recommended: Vermeer HyPower 68
  • V-belt
  • Number of Primary Belts: 2 individual (matched pair) | Number of Secondary Belts: 6 banded