2024 Vermeer® D1000x900 HDD (2) CAT C-18

Information

2024 Vermeer® D1000x900 HDD (2) CAT C-18

Maximize your drilling muscle with the field-tested D1000x900. Loaded with feature after feature to improve performance, reliability and durability, the D1000x900 is equipped with dominating twin Caterpillar C-27 engines, producing a maximum of 92,000 ft-lb (124,735.3 Nm) of rotational torque and 1,000,000 lb (4,448.2 kN) of thrust/pullback.

Features may include:

High-torque, low-speed Hagglunds hydraulic motors

Operates efficiently with high-torque, low-speed Hagglunds hydraulic motors powering the rotary and carriage drives so you can run full torque and full rotary rpm simultaneously.

Thrust box bearing-pack assembly

Reduces stress on the motor, because the thrust box bearing-pack assembly is designed to absorb the axial load caused by thrust and pullback.

Floating vise

Helps prevent rod wrap or windup because its floating vise allows the breakout system to clamp the full rod upsets during breakout of the lower and upper joints.

Higher torque

Muscles through difficult ground formations with higher torque than other models.

Photos

Highlights

  • Texarkana, Texas
  • 2024
  • Vermeer®
  • D1000x900 HDD (2) CAT C-18
  • (2) CAT C-18
  • Diesel
  • Available
  • 8.5 ft | Front Base Anchor: 6 ft | Front Flat Anchor: 5 ft | Rear Base Anchor: 7.8 ft | driller cabin: 8.5 ft | power rack: 8 ft
  • Front Base Anchor: 24 in | Front Flat Anchor: 8 in | Rear Base Anchor: 8 in | driller cabin: 9 ft | power rack: 10.3 ft

Specifications

  • 2024
  • Vermeer®
  • D1000x900 HDD
  • (2) CAT C-18
  • Directional
  • (2) CAT C-18
  • Maximum: 2000 rpm
  • Gross: 1200 hp
  • EPA Certification Family: Tier 3 (EU Stage II)
  • Spindle: 102500 ft-lb | Maximum Spindle Torque (Low at Maximum Engine RPM): 102500 ft-lb
  • Diesel
  • Triple axle with air ride suspension
  • Thrust: 1000000 lbs | Pullback: 1000000 lbs | Breakout Force: 253000 ft-lb | Clamp Force: 250000 ft-lb
  • Maximum Spindle Speed at Maximum Engine RPM (with PS800): 36 rpm | Maximum Spindle Speed at Maximum Engine RPM (with PS1200/PS1600): 54 rpm | Maximum Carriage Speed at Maximum Engine RPM: 77 ft/min
  • Drill Rack Angle: 8 degrees to 12 degrees | Mud Swivel: 3 in | Travel: 6 ft | Inside Diameter: 9.8 in | Inside Diameter: 10 in
  • Minimum: 50.5 ft
  • 8.5 ft | Front Base Anchor: 6 ft | Front Flat Anchor: 5 ft | Rear Base Anchor: 7.8 ft | driller cabin: 8.5 ft | power rack: 8 ft
  • Minimum: 11.5 ft
  • Front Base Anchor: 20 ft | Front Flat Anchor: 9.5 ft | Rear Base Anchor: 16 ft | driller cabin: 10 ft | power rack: 32.2 ft
  • Front Base Anchor: 24 in | Front Flat Anchor: 8 in | Rear Base Anchor: 8 in | driller cabin: 9 ft | power rack: 10.3 ft
  • 1000 gal
  • Tank: 720 gal
  • 101000 lbs | driller cabin: 6000 lbs | power rack: 57260 lbs | lower breakout vise: 3800 lbs
  • Number of Rear Legs: 2 | Heat and Air Conditioning: In-wall combination unit | Number of Rotation Motors: 1 | Number of Drive Motors: 4 | Configuration: 3-jaw clamp, 8 " (20.3 cm) / upper breakout vise: 2-jaw clamp